Pac SWI-RC User Manual download pdf

06-18-10

SWI-RC

Universal Steering Wheel Control Interface

Before You Start

A. Is this product compatible with the vehicle?

• Please visit http://www.pac-audio.com/swixprogramming/swixprogramming.asp for the most current list of

compatible vehicles.

B. Prepare for the installation.

• If possible, install the SWI-RC while you are installing the new head unit. Keep in mind you may need to plug in the

factory stereo to locate certain wires; therefore do not complete the head unit installation until the SWI-RC is work-

ing properly.

• Plan a general installation location for both the SWI-RC plug and the control body. Keep in mind that the supplied

wire harness is two feet long, and the 1/8" plug harness is three feet long.

• Use a multimeter or approved measuring device for checking vehicle circuits.

Pacific Accessory Corporation

SEEK

PRESET

AM FM

VOLUME

PLAY

MUTE

Power

Jack for the SWI-RC

Steering wheel

audio control wire

To Kenwood,

OEM or

Blaupunkt

remote control input

Installation Instructions

For Alpine, JVC, Clarion, Kenwood,

Pioneer, Sony, Valor, OEM, Boyo,

Dual, Visteon, Advent & Blaupunkt

Steering Remote Ready Radios

For Alpine, Clarion, JVC, Pioneer, Sony or Valor radios, connect the SWI-RC 1/8" plug into the radio's Steering

Wheel input jack on back of radio or wire harness. For Kenwood or OEM radios, connect the blue/yel wire to the remote

Input wire (blue/yel or yel/blu for Kenwood, gray for OEM) of radio.

Blaupunkt radios with optional wireless remote inputs are supported by the SWI-RC, however we do not supply

any connectors or support for Blaupunkt. It is up to the consumer or installer to supply this connector. Use vehicle

Connector Chart and use VW connector as reference. Connect the SWI-RC's blue/yel wire to pin #11 of VW connector.

The connector you obtain may come with two of three pieces, however the connector (usually green) should show pin

#11 on it.

Please Note: The SWC input may be located on a

seperate harness instead of the radio chassis. Please refer

to the radio's installation manual before plugging in the

SWI-RC to be certain you are using the correct input to

prevent damage.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Installation Instructions

106-18-10SWI-RC Universal Steering Wheel Control InterfaceBefore You StartA. Is this product compatible with the vehicle?• Please visit http://www.pa

Page 2 - Step 1 - Wiring

2SWI-RCStep 1 - WiringStep A.Connect the BLACK wire to ground (-).Verication: Wire or location registers a constant (-) when probed.Step B.Connect th

Page 3 - SWI-RC interface

306-18-10Step A.Refer to The Vehicle Application Guide or www.pac-audio.com/swixprogramming/swixprogramming.asp for the proper version number. Refer t

Page 4

4Step B.Press and hold program-ming/mode button on SWI-RC. LED will light.Step C.Release programming/mode button. SWI-RCSWI-RCSWI-RCSWI-RCStep 3 - Pro

Page 5 - Appendix A

506-18-10Programming the SWI-RC to Control the Head Unit (cont.)SWI-RCOnce programming is completed, wait 7 seconds. The LED will ash three times ind

Page 6 - Appendix A. (Continued)

6SWI-RCStep F.Repeat Steps D and E, using the TEMP DOWN Button. Step G.If the vehicle is equipped with FAN UP and FAN DOWN buttons:Repeat Steps D and

Page 7

706-18-10Steering Wheel InterfaceConnect SWI whitewire to resistors471001505601000150047 = yel, vio, blk100 = brn, blk, brn150 = brn, grn, brn560 = g

Page 8 - Troubleshooting Guide

8Working on a new or unlisted vehicle?We are always looking for new vehicle information. If you’ve successfully completed the installation on a vehic

Comments to this Manuals

No comments

Pac SWI-RC User Manual

Browse online or download User Manual for For the car Pac SWI-RC. PAC SWI-RC User Manual

Summary of Contents

Comments to this Manuals